Blown in, evenly covered
Loose Fill Insulation
Loose fill is blown in rather than laid in, so it gets into the awkward parts of an attic floor that a cut batt never sits flat against — around joists, wiring and bracing — and builds one consistent blanket at the depth the assembly needs.
Where loose fill goes
- Attic floors brought to an even depth
- Fills around wiring, bracing and odd framing
- Dense-pack options for closed cavities
- Depth markers so coverage is verifiable
Good for
Open attic floors, irregular framing, and topping up insulation that has settled below where it should be. It is usually the best value per point of R-value in an attic.
Worth knowing
It needs a floor to sit on and edges to contain it, so it is not the answer for an open wall cavity or a sloped ceiling. It also should not be blown over material that is wet or damaged — that has to come out first.
What to expect
How a job actually runs
Four stages, in this order, every time — whether it is one attic or an insulation package across a subdivision.
Assessment
We look at the actual building before anyone quotes a number — the attic, the crawl space, and the places air moves between them. You get told what is failing and why, including the parts we would leave alone.
Material Selection
Fiberglass, spray foam, loose fill or batt: the assembly decides, not the price list. We explain which one belongs where and what the difference actually buys you before anything is ordered.
Installation with energy and noise efficiency
Installed for how it performs, not how it looks from the hatch. Full coverage at the right depth, no compressed batts or missed corners, and the air sealing that makes the insulation behave — which is also what makes a house quieter.
Upkeep
Insulation is not maintenance-free. We tell you what to keep an eye on, roughly when it is worth checking, and what a roof leak, a rodent or a duct repair means for the material we just installed.
FAQ
Loose Fill Insulation questions
Loose fill or batts for my attic?
For an open attic floor, loose fill usually wins, because it self-levels around framing and leaves fewer gaps than cut batts. Batts make more sense where the cavity is clean, accessible and needs a defined thickness.
Can loose fill go over insulation that is already there?
Yes, and it is a common and effective combination — the loose fill closes the gaps between and over the existing batts. The exception is if what is underneath is damp or damaged, in which case that comes out first.
Is the install messy?
It is contained to the attic and the route in, the crew masks that route first, and everything gets vacuumed on the way out. You should not be finding loose fill in the house when the job is done.
The jobs it goes into
Where we install it
Where most of the heat moves
Attic Insulation
In a Georgia summer the attic is the hottest part of the house and the biggest gap in its thermal envelope. We bring it up to a real depth in the material the assembly calls for, and seal the ceiling plane underneath first.
Learn moreCold floors and damp air
Crawl Space Insulation
Crawl spaces drive the two complaints we hear most in older houses: floors that are cold all winter, and a humid, musty smell that gets pulled up into the living space. Both are fixable, and both start underneath.
Learn moreOther materials
The dependable default
Fiberglass Insulation
Fiberglass is the most widely used insulation in American homes for good reason: it performs predictably, it costs less than the alternatives, and it suits most standard framed cavities. The whole job is in the fit.
Learn moreInsulates and air seals at once
Spray Foam Insulation
Foam is the answer where a cavity has to be both insulated and sealed, or where there simply is not enough depth to hit the target with anything else. It expands into the gaps that batts and loose fill cannot close.
Learn morePre-cut, for regular framing
Batt Insulation
Batts come pre-cut to standard framing widths, which makes them fast and predictable in walls, floors over crawl spaces, garage ceilings and interior sound walls — wherever the framing is regular and reachable.
Learn moreIs loose fill right for your job?
Sometimes it is, sometimes something cheaper does the same work. Tell us about the assembly and we will give you a straight answer.
OpenMonday – Saturday9:00 AM – 5:00 PM